PORTABLE REVERSE OSMOSIS WATER FILTER
- Compact Portable RO Unit - Adapts to Most Standard Kitchen Taps
- LOW Waste Water Ratio - On Average 1:1
- Highly Economical - As Low as $45.00/Year for Filters *
- Simple Installation - Install and remove in as little as 30 Seconds
NEW Portable Reverse Osmosis Water Filter System
The GT1-70 Portable RO system is great for those looking for great filtered water with no added minerals, this system will give you pure RO water.
This RO Filter is a standard RO that does not contain an alkalising filter.
- Compact Design - Minimise Space for Both Use and Storage
- Completely Pre-Assembled
- Plug And Play - Connects Straight to any standard Kitchen Tap (22-24mm)
- Includes Male Thread adaptor
- Low Waste Water - Averaging 1:1 on average municipal water quality & Pressure)
- Instructions Included
- Pure Water, Removes all the garbage including: Fluoride, Heavy Metals, Chlorine, Chloramines & VOC's, Hardness & Inorganic Mineral Contamination
- Produces approx 190L/Day (Per 24hr)
Thoughts On Fluoride
Fluoride is a hot topic all across Australia and the entire world. Unfortunately, whether or not you agree or disagree with the Fluoridation of Drinking Water, it is there!
Reverse Osmosis Water Filtration is the safest and most effective solution to remove Fluoride from your drinking water.
Fluoride is a proven neurotoxin shown in countless credible studies.
The claimed dental health benefits are irrelevant compared to the known and proven correlation between fluoridated water and Chronic Disease.
Reverse Osmosis water filtration is able to remove Fluoride from the water as it is a Mineral Salt.
Mineral salts will pass straight through standard filtration however the 0.0001 Micron RO membranes are able to remove Fluoride along with other impurities in the water.
- Inline Coconut Carbon Filter 5uM
- Inline Coconut Carbon Filter 5uM post filter
- 50 GPD Asprinn Membrane
- Inlet 22-24mm diverter valve
- Instruction Manual
- Tubing, Clamps & Fittings (Pre-Assembled as per photo)
pH: 6-6.5 when filter stabilises Flow: 8-10L/Hour
Drain Flow: 8-10L/Hour
Dry - 1.5Kg
System Dimensions (Approx)
Height: 10cm Width: 35cm Length: 25cm
NOTE: The diverter valve supplied with this unit suits MOST common standard kitchen taps.
If you have a tap with a thread that does not measure 22mm - 24mm the standard diverter valve will not be compatible.
HOWEVER, if this is the case we have an alternate fitting we can supply you which allows it to be connected to an outdoor 3/4" thread OR the Laundry water inlet (3/4") this is usually the most preferred method of using this system.
PLEASE ensure that you have checked your thread before ordering, if you require the 3/4" fitting, please use check boxes in the listing to select the fitting you want
Stage 1: GAC Inline Carbon Cartridge – replace every 6 months
This 5 micron inline carbon filter acts to protect the stage two membrane.
It will remove the vast quantity of any taste odour or chemicals in the water and help to prolong the life of the membrane.
Stage 2: Asprinn 50GPD RO Membrane (FilmTec Material) - replace every 1 – 4 years
Removes 98% of impurities including organic and inorganic, chemicals.
The membrane, is the "engine room" of the reverse osmosis filtration system.
All the work is done here, so all the filters before the membrane are primarily there to protect the engine.
This membrane will produce up to 50GPD (190L/24hr) of clear pure water @ 70psi within the working feed water quality requirements.
Stage 3: GAC Inline Carbon Cartridge – replace every 12 months
This 5 micron inline carbon filter acts as the final polishing stage post RO membrane, This filter will not add any mineral content back into the water.
Feed Water Conditions
- Pressure: 50 - 100 psi
- TDS: <1,000 mg/L
- Hardness: <250mg/L
- Iron: <0.02
- Manganese: <0.01
- Temperature: 1°C - 26°C
- Flow Rate (Inlet): 1L/Min
Water Production Rate: 8L per Hour (Based on controlled water parameters)
Average pH Output: 6.5 pH NOTE: Use an alkalising RO system for Neutral or Alkaline Water
Initial pH Output: Due to having a post Carbon Filter (GAC) The pH of this unit will initially be high (up to 10.5) Due to a reaction that occurs between the carbon media and pure water.
This pH reading will soon drop back to neutral levels once the water 'vents'
If you are looking for a consistent pH of 6.2 - 6.5 - Use the GT1-70B System.
Inorganic Organic Rejection Aluminum 98% Adrazin Over 98% Arsenic 98% Aldrin Over 98% Benzene Over 98% Barium 95% Chlorine Over 98% Cadmium 95% Chloroform Over 98% Calcium 98% DOT Over 98% Chloride 95% Dichlormethane Over 98% Chromium VI 98% Endrin Over 98% Copper 98% Fluoranthene Over 98% Fluoride 99.9% Herbicides Over 98% Iron 98% Lindane Over 98% Lead 98% Methoxychlor Over 98% Magnesium 98% PCB Over 98% Manganese 98% Pesticides Over 98% Mercury II 85% Perchlorethylene Over 98% Nitrate 90% Phenole Over 98% Potassium 95% Tannic Acids Over 98% Selenium IV 95% Toxaphene Over 98% Silver 98% Trichlorethlene Over 98% Sodium 95% Trihalomethanes Over 98% Strontium 98% V.O.C.'s Over 98% Sulphate 98% Total Dissolved Solids 95% Zinc 98%