AWESOME WATER
CHECK TO MAKE SURE WATER IN
HOT POT VERY IMPORTANT

Extra care should be taken If using a water cooler with a HOT POT OT KETTLE

Hot & cold models
CHECK they is water coming from the hot tap
before turning on power.

CHECK TO MAKE SURE WATER RUNNING VIA HOT TAP BEFORE TURNING ON

​DO NOT boil the kettle 
hot pot if not water coming out of hot tap
IF no water dispensing from hot tap
Wait 10 minutes, for water to fill the hot tank,
they are designed to fill the cold tank up first.

WHEN HOT IS ON THEY IS A RED STEAM LOGO & A RED TRIANGLE GRID

After 10 minutes and still no water via hot taps,
they must be  a airlock, follow next steps

PLACE BOTTLE SET IN BUCKET OR SINK

Remove the bottle set from water cooler
Place in sink or bucket
 
You can push up the float value to stop the water flow if you need to carry...

TWIST AND REMOVE SPINDLE TWO HOLES THUMB AND FOREFINGER

Remove the spindle (white plastic inside cold tank,
​give a twist and pull up,
they should be air bubbles
​releasing the air lock now,

Check before re assembling, by check the hot tap is dispensing
with the spindle off the spike in the cold tank and bottle set off.
 
IF flowing nicely re- assemble
IF still no flow from hot tap, leave 5 minutes, try again 

PROTECT YOUR HOT POT (KETTLE )  
VERY IMPORTANT INFORMATION
For first use OR after you have  completely drained your water cooler via the hot pot etc

MAKE sure that the kettle is FULL  before turning ON your hot water via your water cooler

IF NOT your kettle might trip your power.
​OR many burn the kettle element or even the motherboard.

An airlock will eventually clear itself up over a few hours,
so if you're happy to wait,
just leave the hot water button OFF until you have water coming out of the tap.

WHEN SETTING YOUR WATER COOLER PLEASE REMEMBER
MAKE SURE THEY IS WATER IN THE HOT POT BEFORE TURNING ON..
OR THIS WILL TRIP THE POWER. ( FOR SAFETY)

COLD SIDE ON SNOW FLAKE LOGO BLUE TRIANGLE GRID

Make sure hot water is turned OFF.
There should be no red bars above
​the temperature on he left side.

RED STEAM & TRIANGLE GRID IS A INDICATOR THE HOT SIDE IS TURNED ON

IF you can see red steam bars
OR a red triangle grid 
Push the heat button once,
This will  make a beep sound as it is turning OFF the hot side of your water cooler OFF

FILL YOU WATER COOLER ABOVE THE DOME SO IF CAN REALEASE ANY TAPPED AIR. YOU SHOULD SEE BUBBLES COME OUT OF THE HOLES IN THE TOP OF THE DOME

WATCH YOU WATER COOLER FILL TO MAKE SURE FLOAT VALVE IS WORKING CORRECTLY

Fill your cooler up & wait for the water
to fill the cold tank then you will see
​it fill the bottom bottle set

FILL YOUR COOLER
WILL FILL COLD TANK FIRST
THEN HOT POT

Test the hot water tap 
check if you have a steady
flow of water coming from
the hot tap.
If YES, you can now turn
on the hot water by pressing
the top left HEAT button once.

Leave about 20 minutes to reach required temperature.

ALWAYS CHECK THAT HOT WATER IS DISPENSING VIA HOT TAP BEFORE TURNING ON

TEST HOT SIDE IF WATER IS DISPENSING
IF SO GREAT TURN ON HEAT BUTTON

PLACE BOTTLE SET IN BUCKET OR SINK

IF NO WATER,  REMOVE BOTTLE SET - PLACE IN BUCKET

​IF not water coming out of the hot tap,
you need to  remove the bottle set of the water cooler,  place in a bucket.

REMOVE SPINDLE GIVE A TWIST AND PULL UP TWO HOLES FOR THUMB AND FOREFINGER

You can use other items around your house to release air blockage etc
Options are 
A pipe cleaner to release the airlock
that is in the spike  pipe where the water travels to the hot pot
you can move it up and down a few times to ensure you have cleared all the air bubbles from the spike

REMOVE SPINDLE,
as they is a air lock in the spike.
once you have lifting the spindle you may see bubble of trapped air etc.
Check to see now if water is dispensing from hot tap?. 
IF so you can re - assemble bottle set on top of water cooler and turn the hot side on if using water cooler for hot drinks like coffee, tea, soups, cooking etc  

Other Options
POKE WITH A PIPE CLEANER, CLEAN KEBAB STICK, CHOP STICK, STRAW ETC..
TO REMOVE WATER BUBBLE

Check to see if water is dispensing via hot tap
 
IF so, you can plug you water cooler in via plug to wall and switch on,  
 
They is a switch at the back of the water cooler that needs turning on also.
 
Then press the cool BLUE snowflake button once to turn on the cold side,
this should already be set for 5 deg.