WATER COOLER , NOT HEATING?

WATER COOLER “NOT HEATING”

WATER COOLER NOT HEATING FEB 2020
File Size:	378 kb
File Type:	pdf

Download File

POSSIBLE ISSUES:

1. Check to see if turned on (RED heat button)
2. Check your Hot temperature Settings (>92deg)
3. Motherboard could be burnt out
4. Kettle - hot pot temperature needs resetting
5. Kettle - hot pot element could have burned out

Check if turned ON
RED light triangle grids with hot flames
        To turn on, push the Heat button once
        Will only take 15 minutes to heats up.
   3. Check your hot settings (>92 deg) max

HOT SIDE ON INDICATOR RED STEAM AND RED TRIANGLE GRID

CHECK MOTHER BOARD FOR SIGNS OF DAMAGE

CHECK MOTHERBOARD
FOR ANY SIGNS OF DAMAGE

TURN POWER OFF BEFORE STARTING
(BEST UNPLUGGED)

UNSCREW 2 X SCREWS LOCATED BACK OF WATER COOLER ON THE LID SECTION

Unscrew 2 x screws
located back of water cooler

Remove lid, wiggle to loosen

REMOVE LID ALLOW TO DRAPE LID DOWN THE SIDE OF WATER COOLER KEEPING WIRES IN TAK

Remove Lid,
making sure wires stay together

Unscrew metal box via 2 x screws
at back of machine

IF NO box water cooler <2006 (rare parts)

Check the age of your water cooler. Located at the back of the water cooler is a sticker first 2 numbers are the age you purchased your water cooler

Check signs of damage, burnt out via front, then check back for signs of damage too

Hot may be damaged but cold still OK.

IF Motherboard has signs of damage this needs to be replaced

OTHER ISSUES:
Check that the hot trip switch is NOT the cause of the problem

How to reset the hot trip switch

TURN POWER OFF & UNPLUG BEFORE STARTING

2 X PHILLIPS HEADS SCREW TO REMOVE LID

Removed lid
Remove 2 x screws at the front

2 X SCREWS HIDING BEHIND DRIP TRAY

Remove drip tray
Unscrew 2 x screws behind drip tray

REMOVE LID TO VIEW INSIDE WATER COOLER RECOMMENDED LEAVE WIRES ATTACHED AND ALLOW TO HANG

Unhook the side panels.
Remove front face
Cut stay tie

Remove steel pipe to tap
Check and make sure power is turned off
Push the button, located near blue & black wires
Listen for a click when pushed.
This should now be reset.

IF not, issue is elsewhere

Place a stay tie on the metal pipe

Place rubber pipe onto metal pipe.

Tighten the stay tie

Close up water cooler in reverse order
Clip hooks back

Screws behind drip tray

Screws at front top

Screws at back top

FILL UP with water

TIP LARGE AMOUNTS OF WATER INTO TOP BOTTLE MAKING SURE IT IS FILLED ABOVE DOME TO HELP REALEASE BUBBLE VIA HOLES IN TOP OF DOME 5

NEVER TURN ON HOT SIDE TILL YOU HAVE DISPENSERED WATER VIA HOT TAP

DO NOT
turn on until you have check
to see if they if water flow
from the HOT tap

OTHER ISSUE:

Kettle – Hot Pot has burnt out

If water is still not heating up,
possible cause hot pot

element has burned out,
if so this part needs replacing

CHECK HOT POT FOR WARE AND TARE ISSUES

MOTHERBOARD + ALK STICK

A$75.00 - A$205.00

OPTIONAL EXTRA FILTERS (1 = $50) (2 = $80) (3 = $110) (4 = $130)

WATER COOLER “NOT COOLING”

COULD BE 1 OFF 3 THINGS LISTED BELOW

1. COMPRESSOR SWITCH

2. MOTHERBOARD

3. DIDIBOARD

PRICES VARY DUE TO ADDING EXTRA FILTERS

RECOMMENDED FILTER CHANGE EVERY 6 MONTHS

THE MORE YOU BUY THE MORE YOU SAVE FREE POSTAGE

1. SEE HOW OLD YOUR MACHINE IS

On the back of your water coolers they is a grey sticker. The numbers are green the first 2 number are the year the water cooler was purchased

If older than 2006 – spare parts are rare...

Check list

Check if compressor kick’s in

Turn off your machine for more than 3 minutes, then turn back of with the cool snowflake BLUE button, listen for the compressor to kick in they will be a slight noise like a fridge turning on, can take up to 2-3 minutes your screen should have BLUE triangle grid with a small blue snowflake in the left corner of grid, just above the temperature display panel. You can also place your hand against the right side where the compressor is and you can feel compressor starting.

IF you do not hear a clicking noise the compressor clicking in, then this needs to be replaced

If digital display had faded due to sunlight you can use your hand to cup shade to see screen

1.COMPRESSOR SWITCH

This is located at the back of the water cooler, behind the grilled bars. USE a torch to see easier.

2. MOTHERBOARD

Check list

Check if damaged or signs that it has burnt out.

Remove bottle set of water cooler.

Unscrew 2 x screws located at the back of water cooler

Remove the lid, with a slight wiggle to loosen if needed

Remove Lid, ensuring wires stay in place

They is a metal box unscrew 2 x screws (back of machine)

IF no box earlier modules <2006 (rare parts)

Check for signs of damage on motherboard. (Black burns)

Check front and back.

IF burnt out or damage this needs to be replaced.

3. DIDGIBOARD

Check Didgiboard via the back of lid

For any signs of burnt out or damage

IF signs of damage to the Didgiboard needs replacing

Bench Top & Older Freestanding models (yellow and white plug) 2 pin

Newer Freestanding models with fridge (red, white, and yellow plugs) 3 pin temp control

REPAIR MANUAL